View ISD1810-SERIES_558424.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ISD1810
Single-Chip, Single-Message Voice Record/Playback Device 8- to 16-Second Durations
Advance Information
GENERAL DESCRIPTION
Information Storage Devices' ISD1810 ChipCorder(R) provides high-quality, single-chip, single-message, record/playback solution with user-selectable durations of 8 to 16 seconds. The CMOS devices include an on-chip oscillator (with external control), microphone preamplifier, automatic gain control, anti-aliasing filter, multilevel storage array, smoothing filter, and speaker amplifier. A minimum record/playback subsystem can be configured with a microphone, a speaker, several passive components, two push-buttons, and a power source. Recordings are stored in on-chip nonvolatile memory cells, providing zero-power message storage. This unique, single-chip solution is made possible through ISD's patented multilevel storage technology. Voice and audio signals are stored directly into memory in their natural form, providing high-quality, solid-state voice reproduction.
Figure: ISD1810 Block Diagram
July 2000 ISD * 2727 North First Street, San Jose, CA 95134 * TEL: 408/943-6666 * FAX: 408/544-1787 * http://www.isd.com
ISD1810 Product
FEATURES
* * * Easy-to-use single-chip, single-message voice record/playback solution High-quality, natural voice/audio reproduction Push-button interface - Playback can be edge- or levelactivated * Variable record/playback duration controlled by external resistor selection which sets sample rate. 8 KHz sample rate 6.4 KHz sample rate 5.3 KHz sample rate 4.0 KHz sample rate = = = = 8 seconds 10 seconds * 12 seconds 16 seconds * * No algorithm development required Single +3 volt power supply Available in die form and 28-pin 600 mil DIP (for sampling only) * * * * * * Automatic power-down mode - Enters standby mode immediately following a record or playback cycle - 0.5 A standby current (typical) On-chip 8 9 speaker driver Zero-power message storage - Eliminates battery backup circuits 100-year message retention (typical) 10,000 record cycles (typical) On-chip oscillator
Part Number ISD1810
Minimum Duration1 (Seconds) 10
Maximum Input Sample Rate Typical Filter Upper (KHz)1 Pass Band (KHz)1 6.4 2.6
NOTE
A resistor value of 100 K9 at the ROSC pin provides this specified duration. Only this duration is guaranteed and tested.
ii
Voice Solutions in SiliconTM
Table of Contents
DETAILED DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Speech/Sound Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 NONVOLATILE Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Automatic Power-Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 PIN DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Voltage Supplies (VCCA , VCCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ground Supplies (VSSA, VSSD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Record (REC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Playback, Edge-Activated (PLAYE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Playback, Level-Activated (PLAYL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Record LED Output (RECLED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Microphone Input (MIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Microphone Reference (MIC REF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Automatic Gain Control (AGC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Speaker Outputs (SP+, SP-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 External Clock (XCLK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Resistor Controlled Oscillator (ROSC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Feed Through (FT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FUNCTIONAL DESCRIPTION EXAMPLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 TIMING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PHYSICAL DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ISD
iii
ISD1810 Product
DETAILED DESCRIPTION
SPEECH/SOUND QUALITY
ISD's patented ChipCorder technology provides natural record and playback. The input voice signals are stored directly in nonvolatile cells and are reproduced without the synthetic effect often heard with digital solid-state speech solutions. A complete sample is stored in a single cell, minimizing the memory necessary to store a single message.
AUTOMATIC POWER-DOWN MODE
At the end of a playback or record cycle, the ISD1810 device automatically returns to a lowpower standby mode, consuming typically 0.5 A, provided that Play REC, XCLK, and FT pins are LOW (see DC parameters). During a playback cycle, the device powers down automatically at the end of the message. During a record cycle, the device powers down immediately after REC is released LOW.
DURATION
The ISD1810 devices offer single-chip solutions with 8 to 16 seconds of record/playback duration capacity. Sampling rate and duration are determined by an external resistor connected to the ROSC pin. These specifications apply with the required resistor value for 10-second minimum playback duration.
NOTE Only the 10 second duration is guaranteed and tested.
PIN DESCRIPTIONS
VOLTAGE SUPPLIES (VCCA , VCCD)
Analog and digital circuits internal to the ISD1810 device use separate power buses to minimize noise on the chip. These power buses are brought out to separate pins on the package and should be tied together as close to the supply as possible. It is important that the power supply be decoupled as close as possible to the package.
GROUND SUPPLIES (VSSA, VSSD) NONVOLATILE STORAGE
One of the benefits of ISD's ChipCorder technology is the use of on-chip nonvolatile memory, providing zero-power message storage. The message is retained for up to 100 years without power. In addition, the device can be re-recorded typically over 10,000 times. Similar to VCCA and VCCD, the analog and digital circuits internal to the ISD1810 device use separate ground buses to minimize noise. These pins should be tied together as close as possible to the device.
RECORD (REC)
The REC input is an active-HIGH record signal. The device records whenever REC is HIGH. This pin must remain HIGH for the duration of the recording. REC takes precedence over either playback (PLAYL or PLAYE) signal. If REC is pulled HIGH during a playback cycle, the playback immediately ceases and recording begins.
NOTE The REC signal is internally debounced on the rising edge to prevent a false re-triggering from a push-button switch.
BASIC OPERATION
The ISD1810 ChipCorder device is controlled by the REC pin, and either of two playback pins, PLAYE (edge-activated playback), and PLAYL (level-activated playback). The ISD1810 parts are configured for design simplicity in a single-message application. Device operation is explained on "Functional Description Example" on page 6.
ISD
1
ISD1810 Product
A record cycle is completed when REC is pulled LOW. An end-of-message (EOM) marker is internally recorded, enabling a subsequent playback cycle to terminate appropriately. The device automatically powers down to standby mode when REC goes LOW. This pin has an internal pull-down device. Holding this pin HIGH will increase standby current consumption.
preamplifier. An external microphone should be AC coupled to this pin via a series capacitor. The capacitor value, together with the internal 10 K resistance on this pin, determine the low-frequency cutoff for the ISD1810 passband.
MICROPHONE REFERENCE (MIC REF)
The MIC REF input is the inverting input to the microphone preamplifier. This provides input noisecancellation, or common-mode rejection, when the microphone is connected differentially to the device. Figure 1: ISD1810 Pinouts--For Sampling Only
PLAYBACK, EDGE-ACTIVATED (PLAYE)
When a HIGH-going transition is detected on this input pin, a playback cycle begins. Playback continues until an End-of-Message (EOM) marker is encountered or the end of the memory space is reached. Upon completion of the playback cycle, the device automatically powers down into standby mode. Taking PLAYE LOW during a playback cycle will not terminate the current cycle. This pin has an internal pull-down device. Holding this pin HIGH will increase standby current consumption.
PLAYBACK, LEVEL-ACTIVATED (PLAYL)
When this input pin transitions from LOW to HIGH, a playback cycle is initiated. Playback continues until PLAYL is pulled LOW, an end-of-message marker is detected, or the end of the memory space is reached. The device automatically powers down to standby mode upon completion of the playback cycle. This pin has an internal pull-down device. Holding this pin HIGH will increase standby current consumption.
RECORD LED OUTPUT (RECLED)
The RECLED output is LOW during a record cycle. It can be used to drive an LED to provide feedback that a record cycle is in progress. In addition, RECLED pulses LOW momentarily when an end-ofmessage or end-of-memory marker is encountered in a playback cycle.
NOTE:
NC means must Not Connect.
AUTOMATIC GAIN CONTROL (AGC)
The AGC dynamically adjusts the gain of the preamplifier to compensate for the wide range of microphone input levels. The AGC allows the full range of sound, from whispers to loud sounds, to be recorded with minimal distortion. Nominal values of 4.7 F give satisfactory results in most cases.
MICROPHONE INPUT (MIC)
The microphone input transfers its signal to the onchip preamplifier. An on-chip Automatic Gain Control (AGC) circuit controls the gain of the
2
Voice Solutions in SiliconTM
ISD1810 Product SPEAKER OUTPUTS (SP+, SP-)
The SP+ and SP- pins provide direct drive for loudspeakers with impedances as low as 8 . A single output may be used, but, for direct-drive loudspeakers, the two opposite-polarity outputs provide an improvement in output power of up to four times over a single-ended connection. Furthermore, when SP+ and SP- are used, a speaker coupling capacitor is not required. A single-ended connection will require an AC-coupling capacitor between the SP pin and the speaker. The SP+ pin and the SP- pin are internally connected through a 50 K resistance. When not in playback mode, they are floating.
SPECIFICATIONS
Table 1: Absolute Maximum Ratings1
Condition Junction temperature Storage temperature range Voltage applied to any pad 150C -65C to +150C (VSS - 0.3 V) to (VCC + 0.3 V) -0.3 V to +7.0 V Value
VCC - VSS
1.
EXTERNAL CLOCK (XCLK)
The external clock input for the ISD1810 devices has an internal pull-down resistor. This pin is used for test purposes only. Do not bond this pad.
Stresses above those listed may cause permanent damage to the device. Exposure to the absolute maximum ratings may affect device reliability. Functional operation is not implied at these conditions.
Table 2:
Operating Conditions
Condition Value 0C to +50C +2.7V to +4.5V 0V
(1
RESISTOR CONTROLLED OSCILLATOR (ROSC)
The resistor controlled oscillator input enables the user to vary the ISD1810 device record and playback duration. The resistor connected between the ROSC pin and VSS (R2) determines the sample frequency and the filter upper pass band for the ISD1810 device. ISD recommends an ROSC resistor value of 100 K.
Operating temperature range Play voltage (VCC)
(1)
Ground voltage (VSS)(2) Record Supply voltage (VCC)
1. 2. VCC = VCCA = VCCD. VSS = VSSA = VSSD.
+2.7V to 4.5V
FEED THROUGH (FT)
Feed Through mode allows use of the speaker drivers for external signals. The signal between the MIC and MIC_REF pins will pass through the AGC, the filter and the speaker drivers to the speaker outputs SP+ and SP-. The input FT controls the feed through mode. To operate this mode, the control pins REC, PLAYE and PLAYL are held low at VSS. The pin FT is held high to VCC. For normal operation of record, play and power down, the FT pin is held at VSS. The FT pin has a weak pull down to VSS.
ISD
3
ISD1810 Product
Table 3: DC Parameters
Symbol VIL VIH VOL VOH ICC ISB IILPD1 IILPD2 IILPD3 REXT RMIC, RMICREF AMSP
1. 2. 3. 4. 5. 6. 7. 8.
Parameters Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage VCC Current (Operating) VCC Current (Standby) Input Leakage Current Input Current HIGH Input Current HIGH Output Load Impedance Preamp Input Resistance MIC SP+/- Gain
Min(2)
Typ(1)
Max(2) 0.8
Units V V
Conditions
2.0 0.4 2.4 30 0.5 10 1 30 3 8 10 42 150 400 130
V V mA A A A A K dB
IOL = 4.0 mA(3) IOH = - 1.6 mA(3) VCC = 4.5V
(4) (5)
Force VSS (6) Force VCC (7) Force VCC (8) Speaker Load, SP+ to SP-
AGC = 0.0 V
Typical values @ TA = 25C and 3.0 V. All Min/Max limits are guaranteed by ISD via electrical testing or characterization. Not all specifications are 100 percent tested. Record LED output, RECLED. VCCA and VCCD connected together. REC, PLAYL, PLAYE, XCLK, and FT must be at VSSD. REC, PLAYL, and PLAYE. REC, PLAYL and PLAYE. FT.
Table 4: AC Parameters1
Symbol FS FCF TREC TPLAY TEOM TDB Characteristic Sampling Frequency Filter Pass Band Record Duration Playback Duration EOM Pulse Width Debounce Time 10 10 84 84 Min(3) Typ(2) 6.4 2.6 11 11 Max(3) Units KHz KHz sec sec msec msec
(4)
Conditions
3 dB Roll-Off Point(5)(6)
(4) (4)
4
Voice Solutions in SiliconTM
ISD1810 Product
Table 4: AC Parameters1
Symbol THD Characteristic Total Harmonic Distortion Min(3) Typ(2) 1 Max(3) Units % Conditions @ 1 KHz, VIN = 15 mV Peak to Peak REXT = 8 REXT = 600 Peak-to-Peak(7)
POUT VOUT VIN
1. 2. 3. 4. 5. 6. 7.
Speaker Output Power Voltage Across Speaker Pins MIC Input Voltage
24.4 1.25 15 2.5 300
mW V p-p mV
These specifications apply with ROSC equaling 100 K. Typical values @ TA = 25C and 3.0 V. All Min/Max limits are guaranteed by ISD via electrical testing or characterization. Not all specifications are 100 percent tested. Oscillator stability may vary as much as 5 percent over the operating temperature and voltage ranges. Low-frequency cutoff depends upon value of external capacitors (see Pin Descriptions). Filter specification applies to the antialiasing filter and to the smoothing filter. Balanced input signal applied between MIC and MIC REF as shown in the application example. Single-ended MIC or MIC REF recommended to be less than 100 mV peak to peak.
Figure 2: ISD1810 Application Example--Design Schematic
ISD
5
ISD1810 Product
FUNCTIONAL DESCRIPTION EXAMPLE
The following example operating sequence demonstrates the functionality of the ISD1810 devices. 1. Record a message filling the memory. Pulling the REC pin HIGH initiates a record cycle from the beginning of the message space. The device will automatically power down after REC is released LOW. An EOM marker is written at the end of message. If REC is held HIGH, the recording continues until the message space has been filled. Once the message space is filled, recording ceases. 2. Edge-activated playback. Pulling the PLAYE pin HIGH initiates a playback cycle from the beginning of the message space. The falling edge of PLAYE has no effect on operation. When the device reaches the EOM marker, it automatically powers down. If a recording has filled the message space, the entire message is played. A subsequent rising edge on PLAYE initiates a new play cycle from the beginning of the memory. 3. Level-activated playback. Pulling the PLAYL pin HIGH initiates a playback cycle from the beginning of the message space. When the device reaches the EOM marker, it automatically powers down. If recording has filled the message space, the entire message is played. A subsequent rising edge on PLAYL initiates a new play cycle from the beginning of the memory. 4. Level-activated playback (truncated). If PLAYL is pulled LOW any time during the playback cycle, the device stops playing and enters the power-down mode. A subsequent rising edge on PLAYL initiates a new play cycle from the beginning of memory. 5. Record (interrupting playback). 7. Play back a message that partially fills the memory. Pulling the PLAYE or PLAYL pin HIGH initiates a playback cycle. The playback cycle ceases when the EOM marker is encountered and the device then powers down. 8. RECLED operation. The RECLED output pin provides an activeLOW signal which can be used to drive an LED as a "record-in- progress" indicator. It returns to a HIGH state when the REC pin is released LOW or when the recording is completed due to the memory being filled. This pin also pulses LOW to indicate the end of a message has been reached. 9. ROSC Operation The duration of the device can be varied by changing the value of R2 (ROSC). This means the ISD1810 device can actually be between 8 to 16 seconds duration. See the curve below which charts typical durations when the ROSC is varied from 80 K to 160 K. This feature allows frequency shifting where a recorded voice or sound can be played back faster or slower than normal for special effects. For example, use a 100 K resistor to make the recording and then The REC pin takes precedence over other operations. Any HIGH-going transition on REC initiates a new record operation from the beginning of the memory, regardless of any current operation in progress. 6. Record a message, partially filling the memory. A record operation need not fill the entire memory. Releasing the REC pin LOW before filling the message space causes the recording to stop and an EOM marker to be placed. The device powers down automatically.
6
Voice Solutions in SiliconTM
ISD1810 Product
playback with either an 80 K resistor for faster "chipmunk" talk or with a 120 K resistor for a slower, lower voice. Another feature is a "Pause" or interrupt function that can be done by taking the ROSC resistor to VCC to stop playback momentarily, resuming when the resistor is connected back to ground.
Chart 1:ISD1810 Duration versus ROSC at TA = 25C and 3.0 V
32 16
Typical Duration (sec)
14 28
24 12 20 10 16 8
6
12 80 100 120 140 160
Typical ROSC (K)
ISD
7
ISD1810 Product
TIMING DIAGRAMS
Figure 3: Record Message Until Record Goes LOW
Debounce 84 ms
Operation
Power-Down
Record
Power-Down
PLAYL
PLAYE
REC
RECLED
MIC
INPUT MIC
MIC REF
INPUT MIC REF
Figure 4: Record Message Until Array is Full
Operation Power-Down Debounce 84 ms Record Power-Down
PLAYL
PLAYE
REC
RECLED
MIC
INPUT MIC
MIC REF
INPUT MIC REF
8
Voice Solutions in SiliconTM
ISD1810 Product
Figure 5: Play Edge (PLAYE) Play Until End of Message
Operation Power-Down Debounce 84 ms Play Wink 84 ms Power-Down
PLAYL
Don't Care
No Edges
PLAYE
Don't Care
No Edges
REC RECLED MIC MIC REF
1.2 VOLTS 1.2 VOLTS
SP+ SP-
Open
1.2 VOLTS 1.2 VOLTS
Open Open
Open
Figure 6: Play Level (PLAYL) Play Until End of Message
Debounce 84 ms
Operation
Power-Down
Play
Wink 84 ms
Power-Down
PLAYL
PLAYE
REC RECLED
MIC MIC REF
1.2 VOLTS 1.2 VOLTS
SP+ SP-
Open
1.2 VOLTS 1.2 VOLTS
Open Open
Open
ISD
9
ISD1810 Product
Figure 7: Play Until Play Level (PLAYL) Falls
Debounce 84 ms
Operation
Power-Down
Play
Wink 84 ms
Power-Down
PLAYL
PLAYE
REC RECLED MIC MIC REF
1.2 VOLTS 1.2 VOLTS
SP+ SP-
Open
1.2 VOLTS 1.2 VOLTS
Open Open
Open
Figure 8: Looping Play, PLAYE to RECLED
Debounce 84 ms Debounce 84 ms Play
Operation
Power-Down
Play
Wink 84 ms
PLAYL
PLAYE
REC
RECLED
1.2 VOLTS 1.2 VOLTS
SP+
Open
1.2 VOLTS 1.2 VOLTS
SP-
Open
10
Voice Solutions in SiliconTM
ISD1810 Product
PHYSICAL DIMENSIONS
Figure 9: 28-Lead 0.600-Inch Plastic Dual Inline Package (PDIP) (P)--For Sampling Only
Table 5: Plastic Dual Inline Package (PDIP) (P) Dimensions--For Sampling Only
INCHES Min A B1 B2 C1 C2 D D1 E F G H J S q 0.008 0.070 0 0.015 0.125 0.015 0.055 0.018 0.060 0.100 0.010 0.075 0.012 0.080 15 0.20 1.78 0 0.135 0.022 0.065 0.065 0.600 0.530 0.540 1.445 Nom 1.450 0.150 0.070 0.075 0.625 0.550 0.19 0.38 3.18 0.38 1.40 0.46 1.52 2.54 0.25 1.91 0.30 2.03 15 3.43 0.56 1.65 1.65 15.24 13.46 13.72 Max 1.455 Min 36.70 MILLIMETERS Nom 36.83 3.81 1.78 1.91 15.88 13.97 4.83 Max 36.96
ISD
11
ISD1810 Product
Figure 10: ISD1810 Bonding Physical Layout (Unpackaged Die)
PLAYL PLAYE REC VSSD RECLED VCCD XCLK FT
ISD1810 I. Die Dimensions X: 2530 mils (64,260m) Y: 2420 mils (61,470m) Die Thickness2 11.5 0.5 mil (typ) ISD1810 I. PAD Opening 90 x 90 microns
I.
MIC MICREF AGC SP- VSSA SP+ VCCA ROSC
1. 2.
The backside of die is internally connected to VSS. It MUST NOT be connected to any other potential or damage may occur. Die thickness is subject to change, please contact ISD factory for status and availability.
12
Voice Solutions in SiliconTM
ISD1810 Product
Table 6: ISD1810 PIN/PAD Designations with Respect to Die Center
PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 VSSD REC PLAYE PLAYL N/C N/C N/C N/C N/C MIC N/C MIC REF AGC NC SP- VSSA SP+ VCCA ROSC N/C N/C N/C N/C N/C FT XCLK VCCD RECLED 630.45 358.35 122.15 -126.05 1018.90 1038.70 1038.70 1038.70 -148.15 158.85 465.85 772.85 1007.85 -1024.10 -1037.20 -1024.10 -1037.20 -1037.20 -741.75 -522.35 -1037.20 -1037.20 -977.75 -1037.20 PIN Name X Axis (m) -368.95 -558.95 -760.15 -977.35 Y Axis (m) 1038.70 1038.70 1038.70 1038.70
ISD
13
ISD1810 Product
ORDERING INFORMATION
Product Number Descriptor Key
ISD1810
ISD1800 Series
Duration: 10 =
8- to 16-second duration
Package Type: X= Die P = Plastic Dual Inline Package (PDIP) (For Sampling Only)
When ordering, please refer to the following part numbers which are supported in volume for this product series. Consult the local ISD Sales Representative or Distributor for availability information.
Part Number ISD1810X ISD1810P (For Sampling Only)
For the latest product information, access ISD's worldwide website at http://www.isd.com.
14
Voice Solutions in SiliconTM
IMPORTANT NOTICES
The warranty for each product of ISD (Information Storage Devices, Inc.), is contained in a written warranty which governs sale and use of such product. Such warranty is contained in the printed terms and conditions under which such product is sold, or in a separate written warranty supplied with the product. Please refer to such written warranty with respect to its applicability to certain applications of such product. These products may be subject to restrictions on use. Please contact ISD, for a list of the current additional restrictions on these products. By purchasing these products, the purchaser of these products agrees to comply with such use restrictions. Please contact ISD for clarification of any restrictions described herein. ISD, reserves the right, without further notice, to change the ISD ChipCorder product specifications and/or information in this document and to improve reliability, functions and design. ISD assumes no responsibility or liability for any use of the ISD ChipCorder products. ISD conveys no license or title, either expressed or implied, under any patent, copyright, or mask work right to the ISD ChipCorder products, and ISD makes no warranties or representations that the ISD ChipCorder products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Application examples and alternative uses of any integrated circuit contained in this publication are for illustration purposes only and ISD makes no representation or warranty that such applications shall be suitable for the use specified. The ISD products described herein may not be used in recordable greeting cards intended for resale in Japan without ISD's prior written consent. Recordable greeting cards are articles, usually constructed of paper or cardboard (but not limited to these materials), that include artwork (including preprinted or customer-affixed photographs or artwork) and/or editorials that have the look and feel of greeting cards and are able to be inserted into an envelope (but do not necessarily need to be inserted) and primarily intended to be presented or delivered to an individual as a greeting card, that allow the sender to record and the recipient to play back, and audio signal message. The foregoing restriction applies only to recordable greeting cards intended, directly or indirectly, for retail distribution. Recordable greeting cards incorporating ISD products may not be sold, directly or indirectly, through retail channels without ISD's prior written consent. The 100-year retention and 100K record cycle projections are based upon accelerated reliability tests, as published in the ISD Reliability Report, and are neither warranted nor guaranteed by ISD. Information contained in this ISD ChipCorder data sheet supersedes all data for the ISD ChipCorder products published by ISD prior to August, 1998. This data sheet and any future addendum to this data sheet is (are) the complete and controlling ISD ChipCorder product specifications. In the event any inconsistencies exist between the information in this and other product documentation, or in the event that other product documentation contains information in addition to the information in this, the information contained herein supersedes and governs such other information in its entirety. Copyright(c) 1998, ISD (Information Storage Devices, Inc.) All rights reserved. ISD is a registered trademark of ISD. ChipCorder is a trademark of ISD. All other trademarks are properties of their respective owners.
2727 North First Street San Jose, California 95134 Tel: 408/943-6666 Fax: 408/544-1787 http://www.isd.com
Part No. 2200898D1510

▲Up To Search▲

Price & Availability of ISD1810-SERIES

	To Download ISD1810-SERIES Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .